FireHog MOD-GEM2 Ambi Charging Handle with Gas Exhaust Mitigation | Black AR 15 .223/5.56 (UP-0619260)
100% lifetime Satisfaction Warranty
All new for 2020 the D-Stash GEM-4 Gas Exhaust Mitigation Ambidextrous Charging handle for all AR-15 upper receivers. The D-Stash Charging Handle is 3D machined from a solid block of aircraft grade 7075-T6 aluminum. Its fully independent ambidextrous design allows for seamless operation from either side of the weapon, it aims to alleviate some of the problems with MIL-SPEC Charging handles, without adding excessive weight. The Ambi levers are dual contoured similar to that of the charging handle of an M14, where not only the x-axis but also the y-axis receive radius cuts as well as groves for a grippy thumb placement. The handling surface of the lever is also grove cut, adding a textured grip aiding to the use when operating with gloves. The heightened rear lip of the Stash Handle aids in mitigating gas blow back to the shooter when shooting with short barreled and suppressed weapon systems. All parts are then Type 3 Hardcoat anodized. The D-Stash GEM-4 releases cleanly and easily and is as smooth as butter. Looks great on any setup and without any extra bits, levers, pins or such sticking out.
The GEM-4 Technology Features exquisite gas exhaust technology, all excess gasses traveling towards the rear of the upper receiver will be diverted via the .136" Gas Exhaust Mitigation Port. No more burned up gunpowder residue to the face with every shot. Specifically designed to mitigate excess gas blowback due to suppressed rigs. All excess gas is ported to the right side on the charging handle and diverted away from the shooters face. Look no further for a high performance "Gas Busting" type of charging handle that will perform well under pressure and keep harmful gas ,dirt, and oil out of your face for a more pleasant shooting experience with much less shooters fatigue.
- Gas Exhaust Mitigation Technology
- Ideal for suppressed and SBR setups
- Tactical Ambi Charging Handle w/ Butterfly Latch
- Precision machined from rugged and lightweight 7075 T-6 aluminum.
- Hard coat type II anodized to prevent wearing of surface
- Anodized : Combat Black
- Assembled in USA
14 Reviews Hide Reviews Show Reviews
I installed this charging handle before using my F1 can the first time and was still getting what I believe to be plenty of exhaust gases in my face. Not sure what it would be like to use the original handle on my Sig M400 pistol, but I might try the silicone trick to better seal around the contoured piece between the wings and see if that helps.
COBRATAC: You may be over gassed, try an adjustable gas block.
ran this on my shortie 10" 300 blackout, portsall of the gasses away very well, happy with the purchase .
works just at good at half the price...already bought 3 my self
I bought one of these because the original charging handle I bought (a POF) said it was in stock but they oversold them so they didn't have it I called to see what was up and the guy I talked to was get our firehog charging handle, it's cheaper and better blah blah blah. Well I put it in a 6.5 Grendel I built, it ran perfectly before with a cheap ambi charging handle I had on it. So I put the great firehog in my 6.5 and now it doesn't cycle right. Tried running a few different kinds of ammo and two different mags still cycle problems. Put my cheap charging handle back in it, runs fine again. Not a single cycle problem. So it might work fine in 5.56 but I know for my 6.5 Grendel all it did was create a problem. I would have rather had the POF I originally ordered even if shipping would have taken a month like every other thing they sell that's not their brand. I was surprised I was able to get a hold of customer service tho usually you cant get a hold of no one.
Cobratac Response: we have no reports of firehog charging handles not working on grendel builds.. this would be the first, please start a return request we could exchange the defective handle or refund you your choice.
all I can say is RE-DICKY-TAR-DARD Good !! does all i was hoping for at a very affordable price, well made too with great spring tension and robustness. loving my new firehog products!
Awesome charging handle. Excellent gas mitigation. Can’t go wrong with this
worth every penny
After using almost all the charging handles out there this one is by far the best. I use it on my 7.5 AR pistol .Got so tired of gas in my face ..Everyone should have one of these.You won't be disappointed!
for the money i prefer this over the radian and the cmmg that i have and paid way more for. latches are nice and firm, the the gas mitigation is simple and very effective! i highly recommend this product
This handle is heavy duty and saved my ass in competition. the design is great and i can say by experience that it works very well for constant manual cycling! I shoot competitions and have always used a bcm in the past, I tried the bvlack label and during a stage my gas block loosened on the barrel and the rifle did not cycle. I was able to complete the lane by cycling manually over 30 rounds. The forward cant on the lever really helped me get a good grip as I worked to blade the action under pressure. It wasnt my best time but i can say it wasnt my worst!
The charging handle is extremely well designed, great atention to details. Finish is impeccably good. You get the feeling your holding a very solid product. This company seems to have outstanding QC.
I was looking to upgrade the colt charging handle that came stock on my AR. As I’d previously purchased a Black Label trigger for my AR, I was already very impressed with the quality of their products. So, it was an easy decision to purchase one of their new gen 4 handles as a replacement for the stock one. The handle arrived today and was installed on my weapon. Cobratac has done an outstanding job with this charging handle. Very well made, high quality, handle. Fit and finish is flawless. I’m very satisfied with this purchase. worth every penny and my vote for best bang for your buck!